CSI offers a variety of used modular shielded rooms, anechoic chambers and equipment for sale.
If you don’t find what you are after, contact us, and we may be able to locate what you require.
Click here to get a quote on specific equipment of interest.
Used Probotic Systems 801D Grid Measurement System For Sale
Contact us for pictures and user manual specific to this used item.
If this unit is listed on this page, the item is still available.
Used Antenna Positioner Tower 2071-2 ETS-Lindgren.
The ETS-Lindgren Model 2070-1, 2070-2 and 2071 antenna towers are portable mast and platform systems designed for use in EMI compliance testing at elevations from one to six meters above the ground level. The mast, carrier, boom, platform, drive belts and guying system are non-conductive and non-magnetic. The antenna carrier is raised and lowered by a fractional horsepower electric motor with a gear reducer and electric brake. The electronics are contained in a shielded enclosure and the unit receives signals via fiber-optic cables. The electric drive unit is located at the base of the tower.
The mast sections of the tower are constructed of square fiberglass tubing for strength, rigidity and weatherability. The mast consists of three or four sections, depending on whether a four or six meter height is desired (refer to assembly instructions.) Mylar rope guy lines are provided for outdoor installations and must be firmly anchored to provide vertical stability. The carrier is made of non-metallic material, primarily nylon and delrin.
The motor system drives the carrier up and down using a polyurethane Kevlar reinforced timing belt. Rollers on the carrier provide friction-free, smooth travel. The motor typically positions the carrier within two centimeters of the desired location. To prevent over-travel in either direction of movement, the mechanical limits can be set with dual knobs located outside the motor cover. Soft limits can be set within the mechanical limits using the Model 2090 Positioning Controller.
ETS-Lindgren’s Model 2070-1, 2070-2 and 2071 antenna towers are identical in their rugged construction, toothed belt drives and important safety features. The units are differentiated by features that configure the carrier and boom.
The Model 2070-1 is manually polarized. The Model 2070-2 and 2071 feature centerline air polarization, which enhances measurement accuracy. In addition, the Model 2071 features ETS-Lindgren’s patented Bore Sight system that provides direct antenna aim onto and EUT during scanning.
Contact us for pictures specific to this used item.
If this unit is listed on this page, the item is still available.
Used Copper Screen Room For Sale. Style bottom solid, top 1/2 copper screen P. 12′ x 8′ x 8′. Comes with RCM screen door.
Ideal for shielded room, control room, ante room, etc.
Contact us for pictures specific to this used item. FOB: Ontario, Canada
If this is still listed on this site, the item is still available.
Used ETS-Lindgren 3183 broadband omni-directional antenna For Sale
ETS-Lindgren’s 3183 broadband omni-directional antenna meets the new CISPR 16-1-4 chamber characterization and calibration requirements for measurements above 1 GHz. An operating frequency of 1 – 18 GHz eliminates band breaks, and the 25 W input rating allows signals to be easily detected from the noise floor. Critical VSWR value is 2:1.
The biconical elements are made from aluminum rods and are welded into a fixed assembly. The elements mount onto a balun network which is fabricated of aluminum and the necessary impedance-matching components. Its lightweight construction provides for ease in portability and storage.
If this unit is listed on this page, the item is still available.
We carry used pyramidal (blue) RF absorber. 12″, 18″ and 24″. Ferrite tile.
Contact us for current availability and price.
Used ETS-Lindgren’s Series 5240-18 RF-Shielded Tabletop Test Enclosure 18″x18″x18″ For Sale
Options that this unit has:
- Absorber Lined
- Air Vent (RF Honeycomb Waveguide)
- Internal RF Coupler
- Power/Signal Line Filter
- Connector Panel
Contact us for pictures specific to this used item.
ETS-Lindgren’s Series 5240 RF-Shielded Tabletop Test Enclosures are high performance, portable shielded enclosures designed for fast, convenient EMI/RFI testing and repair. Built to the same reliable shielding standards as full size ETS-Lindgren enclosures, these tabletop enclosures provide effective shielding in a compact, easy-to-use format.
Ease of Operation in a Compact, Portable Format
- Maximum Performance Double Electrically Isolated (DEI)
- RF Door with Toggle Action Over Center Draw Latches
- High-performance 24 oz Copper Shielding Construction
- Shielding Performance of 120 dB+
If this unit is listed on this page, the item is still available.
Used ETS-Lindgren 3301C Active Monopole Antenna For Sale
Contact us for pictures specific to this used item.
The 3301C Active Monopole Antenna is designed to provide reception of an electric field throughout its frequency range, in a single band, without tuning or bandswitching. The 3301C Active Monopole Antenna factor 3 dB roll-off points are at 170 Hz and 30 MHz. Between 250 Hz and 20 MHz, the antenna factor is flat within +/- 1 dB. To prevent saturation by the low frequency signals, the lower 3 dB point is switch-selectable at 170 Hz, 1.9 kHz or 22 kHz. The 3301C is able to sense fields of +7 dB (uV/m) at 1 MHz with a 1 kHz bandwidth. Saturation will not occur below a field strength of 0.8 V/m, resulting in an extremely wide dynamic range to 141 dB. The saturation indicator alerts you of the need to use the internal attenuators.
The model 3301C antenna consists of an stainless steel rod, a counterpoise 61 cm x 61 cm (24 in x 24 in), a broadband high input impedance amplifier built into the base, and an AC power adapter for battery charging (nominal 90 to 265 VAC, 50/60 Hz). The front panel contains controls and indicators include a power switch and power-on indicator, a receptacle and indicator for the battery charger, a grounded female BNC output connector and a signal saturation indicator. Power is supplied by internal AA size rechargeable nickel-metal hydride batteries.
If this unit is listed on this page, the item is still available.
Contact us for pictures specific to this used item.
- FISCHER CUSTOM F-120-1 BCI CLAMP 79 25KHZ – 175MHZ. Used
- FISCHER CUSTOM FCC-BCICF-1 BCI CAL JIG 50Ω 230 10KHZ – 400MHZ. Used
- FISCHER CUSTOM F-CVP-1 Capacitive voltage probe 100Hz – 100MHz. Used
- FISCHER CUSTOM FCC-CVP-CF-1 Voltage Probe Jig 150KHz – 80MHz. Used
- SOLD – Amplifier Research Non – Conductive Tripod TP-1000
- Walker Scientific Inc. ELF-60D/66D Magnetic Field Meter/sensor 40 – 400Hz Used
- Behlman ACP6000-100 AC Power Source DC – 2KHz Used
If these units are listed on this page, the items are still available.
Used ETS-Lindgren 3301C Active Monopole Antenna For Sale
Contact us for pictures and manual specific to this used item.
The ETS-Lindgren Model 3104B BiConLogTM high-field antenna in the bow tie/log periodic family, providing the highest field-to-power ratio at low frequencies of any of the BiConiLog antennas. The Model 3140B is designed specifically to generate the field levels required for immunity/susceptibility tests required by standards such as IEC/EN 61000-4-3 using the lowest amount of input power possible.
A BiConiLog antenna combines a broadband biconical-like bow tie antenna with a standard log periodic dipole array (LPDA) to replace the traditional use of two antennas in the 26 MHz to 3000 MHz electromagnetic compatibility (EMC) test frequency range. Many EMC antennas are variations of a standard tuned dipole, which must be nearly half a wavelength long to transmit or receive energy most efficiently; at 26 MHz, a tuned dipole would have to be approximately 5.3 meters long, 4.6 meters long at 30 MHz, and 2.8 meters long at 50 MHz. This is unwieldy for many anechoic chambers and test sites. The end plates of the Model 3140B T bow ties make the bow tie antenna segment look like an antenna twice as long as the actual 1.6 meter length. The result is about a 10 dB improvement in low frequency transmit gain compared to a regular bow tie of the same length.
If this unit is listed on this page, the item is still available.
Fischer Custom Communications Magnetic Field Immunity Loop FCC F-1000 – Used For Sale
Contact us for pictures specific to this used item.
Model: F1000-4-8/9/10-L-1M
Max. 30A / Continuous
Max. 100A / 2 Hrs
Max. 1000 A / 10 Sec
Coil Factor: 0.88
If this unit is listed on this page, the item is still available.
Foam table used for RF testing (used). Table top dimensions 1mx1.2m.
ETS-Lindgren’s Low Dielectric Tables (LDT) are lightweight, portable test tables, constructed with materials selected for their low dielectric properties. The construction materials for the EUT’s thin support surface have a dielectric constant of <3.0, with each table’s support structures having a dielectric constant of <1.03. The result is a table having virtually no influence on radiated emissions measurements, especially above 1 GHz, where frequencies are affected most. For ease of use and accurate EUT positioning, an EUT placement grid is integrated onto the test table
Contact us for pictures specific to this used item.
If this unit is listed on this page, the item is still available.
SOLD - We have a used 3m chamber for sale.
| Length | Width | Height | |
| Outside dimensions including structure. | 30’ 3¾”9239 | 20’ 7”6274 | 20’ 5”6223 |
| Inside shielded chamber dimensions. | 29’ 6¼”8998 | 19’ 1/8“6023 | 19’ 5 7/8”5939 |
- Modular Woodcore Shielding System
- Structural Steel Support System
- Used manual 48″ x 96″ (4’x8’ opening dimensions) RF Shielded Door.
- Penetration Panel: Used. Size 12×12”.
- 2” diameter RF pipe penetration.
- 1/2” diameter RF pipe penetration.
- Used ETS 60 amp (2 wire) good for 3 phase and 1 used ETS 30 amp (2 wire).
- ½ inch brass grounding stud, set of brass corner caps.
- 6 – 1” sprinkler pipe waveguides with nuts. 6 di-electric breaks are included.
- 4 – 12”x12”honeycomb HVAC waveguides.
- Used ferrite tile. Coverage for all walls and ceiling.
- Used hybrid absorber
Contact us for more information regarding this opportunity. FOB: Ontario, Canada
If this is still listed on this site, the item is still available.
- Absorber Lined
- Air Vent (RF Honeycomb Waveguide)
- Internal RF Coupler
- Power/Signal Line Filter
- Large Connector Panel
- Maximum Performance Double Electrically Isolated (DEI)
- RF Door with Toggle Action Over Center Draw Latches
- High-performance 24 oz Copper Shielding Construction
- Shielding Performance of 120 dB+
| Length | Width | Height | |
| Outside dimensions including structure. | 30’ 3¾” 9239 | 20’ 7” 6274 | 20’ 5” 6223 |
| Inside shielded chamber dimensions. | 29’ 6¼” 8998 | 19’ 1/8“ 6023 | 19’ 5 7/8” 5939 |
- Modular Woodcore Shielding System – New panels and framing
- Includes new sub-floor with pedestals.
- Structural Steel Support System – New Materials, painted blue
- Used ETS-Lindgren manual 48″ x 96″ (4’x8’ opening dimensions) RF Shielded Door.
- Penetration Panel: Used. Size 6×24”.
- 2” diameter RF pipe penetration. Used.
- 1/2” diameter RF pipe penetration. Used.
- Used ETS 60 amp (2 wire) good for 3 phase and 1 used ETS 30 amp (2 wire).
- ½ inch brass grounding stud, set of brass corner caps.
- 6 – 1” sprinkler pipe waveguides with nuts. 6 di-electric breaks are included.
- 4 – 12”x12”honeycomb HVAC waveguides.
- Used SGA ferrite grid panels. Enough coverage for all walls and ceiling.
- Used ETS 600 durasorb polystyrene hybrid absorber with white caps. 242 – 2’x2’ pieces. Comes with white foam bases, ETS-PS-1001, Polystyrene.
- Electric height adjust
- 1 cm height resolution
- Low-stretch polyester rope suspension (750 pound breaking strength)
- Pneumatic polarization standard
- Safety brake
- Zero maintenance
- Absolutely no conductive material above motor box
- Fiber optic interface standard
- Extremely low emissions
- Height and polarization switches located at tower
- Molded, one-piece foot and trolley
- Strong, stable construction
- Easy assembly
SOLD
Used ETS-Lindgren 3117 Double-ridged Waveguide For Sale
Contact us for pictures specific to this used item.
Model 3117 Double-ridged Waveguide is a the latest addition to a family of double ridge waveguide horns for microwave and EMC measurement from ETS-Lindgren. This model corrects the lower gain at the upper end of the frequency range, commonly found in ridged waveguide antennas.
Users of this antenna benefit from uniform illumination of target surfaces and accurate gain measurement. In addition, the 3117 exhibits high gain and low VSWR across its operational frequency band, accepting moderate power input of 300 watts.
The electrical characteristics of this antenna were designed and modeled using powerful workstations running electromagnetic simulation software. Equally important, experienced RF engineers worked with our manufacturing team to produce a practical and affordable realization of the modeling process.
Used ETS-Lindgren SpaceSaver semi-anechoic pre-compliant chamber 25H.
SOLD
Used ETS-Lindgren 3116C Double-Ridged Waveguide Horn Antenna For Sale. 2 units available.
Contact us for pictures specific to this used item.
Frequency Range
The model 3116C sweeps from 10 GHz to 40 GHz without stopping for band breaks, making it ideal for automated testing.
Power Input
This horn antenna accepts up to 20W of continuous input power. The antenna’s high gain and low VSWR over its operating frequency translates into efficient amplifier use and higher field strengths.
SOLD
ETS Lindgren Double Electrically Isolated (DEI) used copper screen room for sale. 13′ x 10′ x 8′.
Ideal for shielded room, control room, ante room, etc.
Contact us for pictures specific to this used item. FOB: Ontario, Canada
Used Amplifier Research FL7006 and FL7000 Isotropic Field Probe Kit/Field Monitor For Sale.
Contact us for pictures specific to this used item.
SOLD
Used TESEQ COMPACT X-WING® BILOG® ANTENNA CBL 6141B For Sale
Contact us for pictures and manual specific to this used item.
The Compact X-Wing® BiLog® For RF EMC emission and immunity testing in compact anechoic chambers. The combination of BiLog® technology with novel low frequency, folded elements (X-Wing®) allows low frequency power to be effi ciently projected forward at 80 MHz without signifi cantly affecting the high frequency elements.
Optimised for Use in Compact Anechoic Chambers
The CBL 6141B X-Wing® has been tuned to 80 MHz to give an immunity performance better than most conventional log periodic antennas. The unique X-Wing® is 30% smaller than the standard BiLog® element, making it ideal for compact chamber testing, especially in the vertical mode where chamber coupling effects occur with large conventional antennas. The CBL 6141B can handle powers up to 300 W at 80 MHz, far in excess of the power required to generate 10 V/m.
Emission Testing 30 MHz – 2 GHz
The CBL 6141B has been designed to give suffi cient 30 MHz performance at a test distance of 3 metres, without the need of a pre-amplifi er.
SOLD
SOLD
Foam table used for RF testing. Table top dimensions 39″x66″. 4″ thick. 31″ high.
Contact us for pictures specific to this used item.
SOLD
Used SUNOL Surface mount TURNTABLE SM46C WITH A USED SUNOL SC99V 2 MODULE CONTROLLER For Sale
Contact us for pictures specific to this used item.
Model SM46C
|
|
Comes with controller.
They feel embarrassed because of the nature of the appliances, its performance level and period of warranty, Look At This viagra prices there is no guarantee that it will work for all men. L-arginine This viagra online india enzyme is an important penis nutrient. Experts say that even if there are no apparent issues related to urinary track, men should get an annual checkup from an expert urologist in viagra in stores Bangalore. The bottom line is that you and your partner can start by amerikabulteni.com buy cheap cialis touching, licking and biting thighs, belly, penis tip and lips.